Aspects SWF213SCT Installationsanleitung PDF herunterladen

SWF213 Fluorescent Semiflush Fixture

Models SWF213

Page 1 of 1 8060613 R1

Safety Precautions

Read all safety precautions and installation instructions carefully

before installing or servicing this fixture. Failure to comply with

these instructions could result in potentially fatal electric shock

and/or property damage.

It is recommended that all wiring be performed by a qualified

electrician. This fixture must be wired in accordance with all national

and local electrical codes.

Do not handle any energized fixture or attempt to energize any

fixture with wet hands or while standing on a wet or damp surface or

in water.

Make sure that the power source conforms to the requirements of the

fixture. (See labels on fixture). Not for use with dimming circuit.

To reduce the risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded. To accomplish proper

grounding, there must be a separate ground wire (green) or bare metal

contact (metal conduit) between this fixture and the ground

connection of your main power supply panel. The green ground

screw location is clearly marked on the fixture housing.

This fixture is intended for use as general indoor lighting in dry or

damp locations only.

Assembly Instructions

1. Preparing for installation

Disconnect electrical power before installing or servicing any part of this fixture.

A. Install canopy mounting screws (2) through center screw holes. Attach

mounting plate (1) to junction box (not provided) in position shown with #8-32 x

1-1/2” screws provided.

B. Pull the wires tight and cut cord allowing for 6 inches of wire for junction box

wiring. Carefully remove outer insulation from cord without damaging lead

wires. Strip lead wires back 3/8 inch for wire nut connections. WARNING:

Inspect modified cord and wires for any damaged insulation.

C. Install four decorative bars (6) to canopy by securing them with short screws and

ball nuts (7) (Note – turning the assembly up-side-down may make threading the

screws easier).

2. Wiring

All wiring must take place inside junction box. Caution: Make sure power

is off at fuse or circuit breaker box. Check power wires for damage or scrapes. If

power supply wires are within three inches of ballast use wire suitable for at least

90C (194F). Note: Most dwellings built before 1985 have supply wire rated to 60C.

Consult a qualified electrician before installing.

A. Feed cord through center hole in mounting plate (2).

B. Securely attach green wire to ground supply wire and ground screw located in

mounting plate.

C. Using wire connectors provided, connect white supply wire to white fixture lead.

Connect black hot supply wire to black fixture lead. Do not mix wires. Pull on

each wire lead to make sure connections are secure. Make sure no bare wires are

exposed outside of wire connectors.

3. Fixture mounting

A. Install fixture threaded end through the canopy central hole and secure it with plate (4) and nut (3).

4. Lamping

A. Install two 13-watt self-ballasted compact fluorescent spiral lamps (8) into socket by inserting pins into holder and twist until it

snaps in place.

CAUTION - RISK OF FIRE, Max. 13-watt type GU-24 (provided), TCP 33113SP or Maxlite MLS13GUWW recommended for

replacements only.

5. Diffuser mounting

A. Install glass diffuser (9) over threaded rod and secure with and plastic plate (10), iron plate (11) and nut (12).

B. Install cap (13) over threaded rod and secure it with the knob (14).

6. Power to the fixture can now be restored

Limited Factory Warranty

American Fluorescent Corporation hereby warranty that this fixture is free from defects in materials and workmanship when installed and used under normal operating

conditions for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or components; it

does not cover failure due to improper installation, misuse, mishandling or damage incurred in transit.

Safety Precautions 1

Inhaltsverzeichnis

Seite 1 - Safety Precautions

SWF213 Fluorescent Semiflush Fixture Models SWF213 Page 1 of 1 80

Kommentare zu diesen Handbüchern

Keine Kommentare

Ao smith 405 Series Manuale Utente (12 pagine)

Marchio: Ao-smith | Categoria: Water boiler | Dimensione: 0.20 MB |

Indice

GAS-FIRED COMMERCIAL

REPLACEMENT PARTS LIST

JACKET ASSEMBLY COMPONENTS

WATER HEATER CONNECTIONS

CONTROL BOX ASSEMBLY

WIRE HARNESS

IRI/CSD-1 COMPONENTS

Più prodotti e manuali per Bollitori per acqua Ao-smith

Modelli	Tipo di Documento
Genesis GW-1500	Manuale Utente A.O. Smith Genesis GW-1500 User Manual, 2 pagine
BTH 300	Manuale Utente A.O. Smith BTH 300 User Manual, 1 pagine
Water Heater	Manuale Utente A.O. Smith Water Heater User Manual, 36 pagine
10	Manuale Utente A.O. Smith 10 User Manual, 11 pagine
HW 300 THRU HW 610	Manuale Utente A.O. Smith HW 300 THRU HW 610 User Manual [en] , 2 pagine
BT- 65	Manuale Utente A.O. Smith BT- 65 User Manual [en] , 1 pagine
BT 65 Series 100	Manuale Utente A.O. Smith BT 65 Series 100 User Manual, 2 pagine
BT180-100	Manuale Utente A.O. Smith BT180-100 User Manual, 1 pagine
960 through 967	Manuale Utente A.O. Smith 960 through 967 User Manual, 74 pagine
DB-720 thru 1810	Manuale Utente A.O. Smith DB-720 thru 1810 User Manual, 4 pagine
BTP-139A	Manuale Utente A.O. Smith BTP-139A User Manual [ru] , 2 pagine

Aspects SWF213SCT Installationsanleitung