Model: 326928
1 of 1
Limited Factory Warranty
American Fluorescent Corporation warrants this fixture is free from defects in materials and workmanship when installed and u
period of 2 years from date of purchase. This
due to improper installation, misuse, mishandling or damage incurred in transit
Read all safety precautions and installation instructions carefully before
installing or servicing this fixture. Failure to comply with
instructions could result in potentially fatal electric shock and/or
property damage.
It is recommended that a qualified
fixture must be wired in accordance with all national and local
electrical codes.
Do not
handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a wet or damp surface or in water.
1.
Preparing for installation
A. Disconnect electrical power
at fuse or circuit breaker box before installing or servicing any part of this fixture.
B.
Carefully remove the fixture from the carton, and check that all parts are included, as shown in figure below. Be careful not
of the screws or part
s which are needed for installing the fixture.
A. Assemble 5 glass panels
B.
Place diffuser (2) on the frame bottom;
C.
Place four diffusers (3) on frame sides.
secure the glass panels.
2. Wiring-all wiring
must take place inside junction box.
Caution:
Make sure power is off at fuse or circuit breaker box. Check power wires for
damage or scrapes. If power supply wires are within three inches of
use wire suitable for at least
wire rated to 60C. Consult a qualified electrician before installing.
D. Secure gem bar (4) on the
F. Make all wire connections
to appropriate wire. Secure
G. Connect the green wires
from the fixture and power source to the green screw on the gem
bar (4).
H.
The black wire from the fixture is connected to the black wire from power source.
I. The white w
ire from the fixture is connected to the white (neutral) wire from power source.
G.
Tuck all connections neatly into junction box.
3. Mounting
A. Thread nut (7) on stem (6
). Adjust the length of the stem in the gem bar so that approx.
is exposed.
Secure the necessary length with nut (7).
B. Install back panel (8
4. Place the frame (11)
5
. Restore power at fuse or circuit breake
American Fluorescent Corporation warrants this fixture is free from defects in materials and workmanship when installed and u
period of 2 years from date of purchase. This
warranty covers all component parts and extends only to replacement of defective fixture or components; it does not cover fai
due to improper installation, misuse, mishandling or damage incurred in transit
Read all safety precautions and installation instructions carefully before
installing or servicing this fixture. Failure to comply with
these
instructions could result in potentially fatal electric shock and/or
It is recommended that a qualified
electrician perform all wiring. This
fixture must be wired in accordance with all national and local
handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a wet or damp surface or in water.
Preparing for installation
at fuse or circuit breaker box before installing or servicing any part of this fixture.
Carefully remove the fixture from the carton, and check that all parts are included, as shown in figure below. Be careful not
s which are needed for installing the fixture.
metal frame (1):
Place diffuser (2) on the frame bottom;
Place four diffusers (3) on frame sides.
Fold four metal tabs to
must take place inside junction box.
Make sure power is off at fuse or circuit breaker box. Check power wires for
damage or scrapes. If power supply wires are within three inches of
94F). Note:
Most dwellings built before 1985 have supply
wire rated to 60C. Consult a qualified electrician before installing.
supplied) with two screws (5)
to appropriate wire. Secure
with wire nuts
from the fixture and power source to the green screw on the gem
The black wire from the fixture is connected to the black wire from power source.
ire from the fixture is connected to the white (neutral) wire from power source.
Tuck all connections neatly into junction box.
). Adjust the length of the stem in the gem bar so that approx.
Secure the necessary length with nut (7).
6) and secure it with the thumbnut (10).
backpan screws and secure it
. Restore power at fuse or circuit breake
r box.
120VAC / 60Hz
American Fluorescent Corporation warrants this fixture is free from defects in materials and workmanship when installed and u
sed under normal operating conditions for a
warranty covers all component parts and extends only to replacement of defective fixture or components; it does not cover fai
This fixture is designed for use in a 110
Do not use on a dimming circuit.
To reduce the
risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To accomplish proper
grounding, there must be a separate ground wire (green)
between
this fixture and the ground connection of your main power
supply panel.
This fixture is intended to be used for general
damp locations only.
at fuse or circuit breaker box before installing or servicing any part of this fixture.
Carefully remove the fixture from the carton, and check that all parts are included, as shown in figure below. Be careful not
Make sure power is off at fuse or circuit breaker box. Check power wires for
power supply,
Most dwellings built before 1985 have supply
ed)
).
from the fixture and power source to the green screw on the gem
The black wire from the fixture is connected to the black wire from power source.
ire from the fixture is connected to the white (neutral) wire from power source.
). Adjust the length of the stem in the gem bar so that approx.
1”
2).
8060664 R1
sed under normal operating conditions for a
warranty covers all component parts and extends only to replacement of defective fixture or components; it does not cover fai
lure
120VAC, 60Hz fused circuit.
risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To accomplish proper
grounding, there must be a separate ground wire (green)
contact
this fixture and the ground connection of your main power
This fixture is intended to be used for general
outdoor lighting in dry or
Carefully remove the fixture from the carton, and check that all parts are included, as shown in figure below. Be careful not
to misplace any
Kommentare zu diesen Handbüchern